Please note, if you click and buy through links on our site, we may earn a small affiliate commission at no extra cost to you. Learn More
A PoE switch sends power and video data over one Ethernet cable per camera. Its powered ports and shared power budget determine how many cameras it can support.
My top pick is the TP-Link TL-SG1210MP. It has eight PoE+ ports, a 123 W shared budget and two uplink connections, so the router and recorder can each have their own port.
My second pick is the TP-Link Omada ES205GP. It fits up to four cameras and offers VLAN controls if you want to keep camera traffic separate.
The TL-SG1210MP is my first choice for a straightforward wired system of up to eight cameras. All eight camera ports support PoE+, and the two unpowered uplinks let you connect a recorder and the rest of the network without giving up a camera port. The combo uplink takes either an Ethernet cable or a compatible fiber module. Both connectors share one logical port.
I’d pick this for a mix of fixed cameras and a PoE+ doorbell or PTZ, provided the total fits the 123 W budget. It has PoE Auto Recovery, which can power-cycle an unresponsive device, and the fanless switch can sit near the recorder in a home office. For a network that needs tagged camera VLANs, choose a managed model. The physical Isolation Mode switch only offers preset port separation.
- Eight powered ports with a 123 W shared budget
- Two uplinks keep camera ports free
- Fanless with PoE Auto Recovery
- No configurable VLANs
- PoE+ output only
The Omada ES205GP suits a doorbell and a few fixed cameras, or a small shop with two cameras inside and two outside. Four PoE+ ports share 65 W, and the fifth jack connects to the rest of your network. The switch is about four inches wide and can go on a shelf or wall indoors.
Use it as a plug-and-play switch to get the cameras online, or set up an 802.1Q VLAN if the rest of your network supports one. You can manage it locally in standalone mode or add it to an Omada Controller. TP-Link reserves automatic PoE recovery for standalone mode. Under controller management, recovery is manual.
Four cameras fill every powered jack. If you plan to add a fifth camera or want to plug the recorder directly into the switch with all four camera ports occupied, buy a switch with another Ethernet port or connect the recorder elsewhere on the LAN.
- Four PoE+ ports plus a Gigabit uplink
- 802.1Q VLANs on a compact switch
- Local management or Omada Controller support
- Four powered ports leave limited room to expand
- Automatic PoE recovery works in standalone mode only
The GS316PP is the one I’d choose for a larger group of fixed cameras on a simple network. The included 200 W power adapter gives it a 183 W PoE budget, so there’s room for a dozen 10 W cameras if the switch allocates power near their rated draw. The switch is fanless and can sit on a desk or mount to a wall.
Every jack is a Gigabit PoE+ port. Plan for at most 15 directly connected cameras if one jack goes to the LAN, or 14 if the recorder takes a second jack on the switch. The similar GS316P ships with a smaller adapter and a 115 W budget. Check for the extra P in the model number if you’re buying for a load close to the limit.
- 183 W PoE budget with the supplied adapter
- PoE+ on all 16 Gigabit jacks
- Fanless desktop or wall placement
- Uplink takes a port that could otherwise power a camera
- No SFP uplink or configurable VLANs
The UniFi Ultra 60W is a good fit when several camera cables meet in a dry indoor spot away from an outlet. Run one cable from a compatible PoE++ source into the Ultra’s Gigabit input port. That cable carries the uplink traffic and gives the Ultra up to 42 W to share across its seven PoE+ outputs. Check what that upstream switch can supply across all its devices, including the Ultra.
With an outlet nearby, the included 60 W adapter raises the output budget to 52 W. Powering the switch from PoE+ drops that budget to 16 W, which is too little for many groups of cameras. I’d use the Ultra for a handful of low-draw cameras on an existing UniFi Network setup. The PoE++ marking refers to its input port. Cameras that need PoE++ output need a different switch.
- A PoE++ uplink can power the switch and downstream cameras
- Seven Gigabit PoE+ outputs
- 60 W adapter included with this variant
- Downstream power depends on the input source
- Managed through UniFi Network
The Pro Max 16 PoE is for a system with one or more cameras that call for 802.3bt Type 3, such as a high-power PTZ. Four 2.5 GbE ports can each supply up to 60 W at the switch, and another twelve Gigabit ports supply PoE+ for fixed cameras. Two SFP+ slots can carry an uplink without using a powered port. You’ll need compatible hardware at both ends to use them.
All sixteen copper ports share 180 W. Four devices drawing the full 60 W at the switch would need 240 W before you connect any fixed cameras. This model makes more sense for a mixed load, particularly if you already use UniFi Network and want to manage camera VLANs there. Factor in the separate mounting kit if you need to rack-mount it.
- Four 60 W PoE++ ports for compatible high-draw cameras
- Two dedicated 10 GbE SFP+ uplink slots
- VLAN support through UniFi Network
- 180 W shared budget cannot supply all four PoE++ ports at full power
- Rack mount is a separate purchase
How to Choose a PoE Switch for Security Cameras
Match the PoE standard on every camera
Look up the power requirements for the exact camera model, including any heater or illuminator you plan to use. Standard PoE (802.3af) supplies up to 15.4 W at the switch, and PoE+ (802.3at) supplies up to 30 W under the standard. The camera can receive less after cable losses. If the camera calls for 802.3bt, check the required type or class. A switch with 60 W Type 3 ports is only suitable if it meets that camera’s requirement.
Add up the maximum power draw
Check the maximum for each camera with infrared lights, spotlights or heaters running where applicable. For example, six cameras rated at 9 W and two rated at 14 W total 82 W at the cameras. An 83 W switch would leave only 1 W before cable losses or extra power reserved by the switch. A 123 W model gives that installation more room, provided its power allocation and each camera’s PoE class fit. Include any other powered device sharing the switch and run your figures through the PoE power budget calculator.
Leave a port for the uplink
Count one powered port for each camera. Then allow a data port for the link back to your network and another if your recorder will plug directly into the same switch. Dedicated uplinks are handy when every camera port is in use. Add the configured bitrates of the streams that will cross the uplink. Eight cameras sending 8 Mbps each use about 64 Mbps for those streams, so a Gigabit uplink has room for that recording load. Also check the recorder’s incoming bandwidth limit.
Choose managed if you need a camera VLAN
An unmanaged switch is easy to set up for a standalone system or an existing camera network with no per-port configuration needs. A managed switch can assign camera ports to a VLAN, but the rest of the network needs to carry that VLAN too. If the recorder sits on a different network, configure routing and firewall rules so it can still reach the cameras. Check discovery and recording before moving every camera across.
Check cable length and switch placement
Standard Gigabit copper Ethernet runs are up to 100 m (328 ft), including patch leads. Keep these switches in a dry location within their specified operating range. For a longer path, consider fiber to a second switch with its own power near the cameras. Fiber carries the data back to the recorder, and the second switch supplies power over the final copper runs.
Common Questions About PoE Camera Switches
Do I need a separate PoE switch if my NVR already has camera ports?
You can use the built-in PoE ports if they match your cameras and all the cables reach the recorder. A separate switch helps when the camera runs come together somewhere else or you use a recorder without powered ports. Follow the NVR’s instructions for LAN-connected cameras. A switch adds Ethernet ports, while the NVR’s channel limit still determines how many it can record. See the PoE NVR buying guide if you’re choosing the recorder too.
Can cameras from different brands share a PoE switch?
Yes, if their PoE standards match the switch ports and the combined load fits its budget. Check recording compatibility separately. A switch can power and connect a camera even when the recorder can’t add it or use all its features. For mixed setups, check the camera and recorder compatibility guide.
Conclusion
For an installation of up to eight cameras that fits a 123 W budget, I’d buy the TP-Link TL-SG1210MP. If you have four camera runs or fewer and want the option to configure a VLAN, choose the TP-Link Omada ES205GP. For a larger system, decide whether you need more powered jacks or a higher PoE class before you move up to a 16-port model.